Set Heavy Duty

2 Sets Heavy Duty 12 Black Linear Actuator Stroke 225 Lb Pound Max Lift 12V DC

2 Sets Heavy Duty 12 Black Linear Actuator Stroke 225 Lb Pound Max Lift 12V DC
2 Sets Heavy Duty 12 Black Linear Actuator Stroke 225 Lb Pound Max Lift 12V DC
2 Sets Heavy Duty 12 Black Linear Actuator Stroke 225 Lb Pound Max Lift 12V DC

2 Sets Heavy Duty 12 Black Linear Actuator Stroke 225 Lb Pound Max Lift 12V DC    2 Sets Heavy Duty 12 Black Linear Actuator Stroke 225 Lb Pound Max Lift 12V DC

2 Sets Heavy Duty 12 Black Linear Actuator Stroke 225 Lb Pound Max Lift 12V DC. 0.47 in/sec (12 mm/sec). 12 Volt DC, 12 inch Extension. Retracted length: 16.13(410mm). Extended length: 28.13(714mm).

Diameter of Mounting hole: 0.256(6.5mm). Diameter of Shaft: 0.79(20mm). Built-in clutch prevents over-extending and over-compressing. Professional Installation is Highly Recommended (No Instruction and Wiring Diagram Included).

Please refer to the more choice listing. The total load on the actuator (structure weight, structure friction, and possible actuator friction) must be less than or equal to the rated load of actuator. The moving load must be centered above the actuator extension tube so that actuator lifting point is located at the center-of-mass of the structure. Unless the structural design is properly braced, off-centered loads will cause additional friction that can (1) exceed the rated load of the actuator or (2) cause the actuator shaft to bend and permanently fail.

Do not exceed the 25% duty cycle of the actuator: If the actuator is used at full load for 2.5 minutes, then it must remain off for 7.5 minutes. Exceeding the duty cycle will cause the actuator motor to overheat and permanently fail.

Mount the actuator by securing the top and bottom mounting holes to two fixed positions. The stroke length of the actuator e. 12 inches and the limitations of the particular application will determine the location of the fixed mounting positions. IMPORTANT: Confirm that up/down movement of the actuator is smooth and within the actuators stroke length after installation. Secure the top and bottom mounting holes of the linear actuator onto the two mounting fixtures using 5/16 diameter bolts. DESCRIPTION --12 Volt DC, 12 inch Extension. -Black Steel --225 Pound Max Lift.

-Retracted length: 16.13"(410mm) --Extended length: 28.13"(714mm) --Diameter of Mounting hole: 0.256"(6.5mm) --Diameter of Shaft: 0.79"(20mm) --Wiring included, pre-installed. -Built-in clutch prevents over-extending and over-compressing. -Professional Installation is Highly Recommended (No Instruction and Wiring Diagram Included). The item "2 Sets Heavy Duty 12 Black Linear Actuator Stroke 225 Lb Pound Max Lift 12V DC" is in sale since Friday, August 18, 2017. This item is in the category "Business & Industrial\Automation, Motors & Drives\Rotary & Linear Motion\Linear Actuators".

The seller is "demotorperformance" and is located in United States. This item can be shipped to United States, Canada, United Kingdom, Mexico, Germany, Japan, France, Australia, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Greece, Portugal, Cyprus, Slovenia, Sweden, South Korea, Indonesia, Taiwan, South africa, Thailand, Belgium, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Austria, Bahamas, Israel, New Zealand, Philippines, Singapore, Switzerland, Norway, Saudi arabia, Ukraine, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Chile, Colombia, Costa rica, Dominican republic, Panama, Trinidad and tobago, Guatemala, El salvador, Honduras, Jamaica, Belize, Bolivia, Ecuador, Egypt, Jordan, Cambodia, Maldives, Peru, Viet nam, Uruguay.

  • MPN: 2*DMTRL14-12BK
  • Brand: Demotor Performance
  • Bundle Listing: Yes
  • UPC: Does not apply


2 Sets Heavy Duty 12 Black Linear Actuator Stroke 225 Lb Pound Max Lift 12V DC    2 Sets Heavy Duty 12 Black Linear Actuator Stroke 225 Lb Pound Max Lift 12V DC